Anker’s Ultra Slim Extended Battery Case provides the best mix of good performance, price for that capacity, and physical size (the level of bulk it boosts the phone). It offers the capacity to provide 117 percent of any full charge for an iPhone 6 or 108 percent to a iPhone 6s. The cost tag, $40 at this particular writing, is crazy low for the battery case: At that rate, the Ultra Slim provides the best charge value (a 2.9 percent charge per dollar, or $34.34 for any full charge, to the iPhone 6) of any of the cases we tested, certainly.
The Ultra Slim doesn’t have an especially premium feel. That’s not to imply which it comes off as cheap, but nothing about its physical construction is very impressive close to other cases. Another minor strike against this Anker case is its lack of button coverage; we typically prefer (well-designed) press-through button covers that protect the iPhone’s various buttons and minimize the quantity of places where dust and dirt could get beneath the iphone6 case manufacturing.
To the iPhone 6 Plus and 6s Plus
Anker doesn’t make an Ultra Slim for the iPhone 6 Plus or 6s Plus, so for all those handsets, we love the Tylt Energi Sliding Power Case. Unlike many of the models we tested, this one includes a separate protective case that you could slide out of the battery sled whenever you don’t want the extra power, so that it is a much more-practical option for the already huge Plus models. It’s another great source of energy, providing normally a 93 percent charge to the iPhone 6s Also in our tests.
A significant thing to not forget with all the cases we dismiss below is they are certainly not necessarily bad. Although we’re noting any issues we saw using these cases, a few of them are fine-they only can’t quite match towards the high quality of our own picks.
Our previous pick for a more protective case was Speck’s CandyShell. A perennial favorite, they have two layers of material-plastic on the exterior, rubber on the inside-offering more protection than case designs which are just one or maybe the other. The CandyShell is 10.9 mm thick, which puts it about the chunky side, however it doesn’t feel exceptionally bulky, and it’s one of the only cases we tested which claim to satisfy military drop-test standards. Speck gives the case in a wide range of colors, and variants add rubbery grips (CandyShell Grip), credit card holders (CandyShell Card), and graphic prints (CandyShell Inked).
The CandyShell has a few conditions that make it from being a top pick, though. For starters, the CandyShell’s glossy back very quickly attracts small scratches that generally aren’t visible head on but jump out if you observe the iPhone in an angle. Granted, these scratches don’t impact the protection the truth offers-and we’re obviously happier to see scratches on the case rather than in the phone itself-but it would be nice if Speck were to offer the case by using a matte finish.
One other dilemma is the case’s shape. Some of our readers, in addition to a contingent of Amazon reviewers, take trouble with the point that the CandyShell’s back is slightly convex. Specifically, once you set the case over a flat surface, this “hump” causes the way it is to rock whenever you press along any one of its edges, or even to spin such as a top in the event you push it. (When you got a new CandyShell and you also mind this spinning and rocking, Speck says to contact its customer care department.)
OnePlus (the Android phone maker) surprisingly decided to get in in the iPhone-case game using its Sandstone Case. The major draw is OnePlus’s Sandstone texture; TIME states that it “feels like smooth sandpaper” which “[i]t’s super grippy, making it very difficult to drop.” Unfortunately the truth is actually a shell with open top and bottom edges, meaning it’s less protective when compared to a good case should be. Because of this design drawback, it fell out from competition.
SwitchEasy includes a mixed history, one which makes it challenging to tell the entire story based on its cases alone. Its Numbers case was our original pick to the iPhone 5 and 5s, before a wave of reader complaints about quality and customer satisfaction. The answers we got from SwitchEasy weren’t thorough; mostly, the corporation blamed the issues on third-parties selling knockoffs of its products. (At iLounge, I discovered the SwitchEasy protectors being impressive generally speaking-the Numbers earned a rare A rating from me-but readers there contacted me about similar issues.) Ultimately, we pulled our recommendation.
With all of that under consideration, we looked at three SwitchEasy cases to the iPhone 6. The first is the Odyssey. Like several of the better cases we’ve evaluated, it’s a combination of plastic and rubber. As opposed to being layered, materials run next to each other, together with the hardened rubber making up the majority of the case. It isn’t the prettiest case, in our opinion, however it is protective. It covers the buttons without reducing most of their clickiness, and six holes along the bottom line up precisely together with the speaker vents. The most popular section of the case is definitely the port protection: Rubber protectors squeeze into the headphone and Lightning ports, respectively, when they’re not in use, keeping dust as well as other debris out.
SwitchEasy’s Tones includes the same port protection and uses the same materials. Your body is generally plastic, though, using the rubber walking around the sides like a border as well as across the back of the case, matching the iPhone’s antenna lines. We’d should you prefer a layer of rubber involving the handset along with the plastic back of your TPU iphone6 case, and the Sleep/Wake button demands a bit excessive pressure about the few units we tested.
Our initial impressions of SwitchEasy’s Numbers were very positive-we were ready to name it as being our top pick-but there’s far more to the story than only our review units, and that we found a substantial fault after some extended use. This situation is virtually identical to the Incipio NGP, nevertheless it offers more protection. Instead of leaving the phone’s ports totally exposed, the way it is provides protectors that fit to the headphone-jack and Lightning-port openings to hold dust and debris out. It’s a nice touch that’s executed well. The phone’s speaker is preferable protected, with six individual holes as an alternative to one long opening. We actually like the tactility of your devqpky94 much more with SwitchEasy’s model compared to Incipio’s case, too. An earlier yellow version from the case we tested accumulated permanent stains, but later iterations exhibited no such issue. The problem is that the case is too loose, and so the corners appear too easily. We experienced this problem over and over while eliminating the encased phone from our pockets. Because we’ve had other problems with SwitchEasy cases in past times, we’re still somewhat wary. If you choose to buy a SwitchEasy case, we recommend buying it directly through the company’s website. Doing this will eliminate any potential warranty issues with third-party sellers, should you have any troubles with the case.
An essential thing to not forget with the cases we dismiss below is the fact that, unlike with many other groups of products we cover, they are not necessarily bad. Although we’re noting any issues we saw using these cases, some of them are fine-they only can’t quite match towards the good quality of our picks.
Combining a rubber skin with a plastic frame, the Spigen Neo Hybrid is a slim, attractive case. Its fatal flaw is in its button protection. The silver plastic pill within the Sleep/Wake button doesn’t depress properly, so it may not hit the control underneath, so you likely won’t feel it when it does. Former Sweethome editor Joel Johnson confirmed this concern together with the iPhone 6 Plus version. Because we received this example for testing so early, we think Spigen might revise later editions to manage this problem.
Also from Spigen is definitely the Ultra Hybrid, a single-piece case that fuses a rubber frame with a clear plastic back. It’s a great-looking case, but when again, they have difficulties with the buttons. Rather than putting raised material over them, they have left and right edges which are flat from top to bottom with small indentations. For that Sleep/Wake button, the indented label says “PWR,” and for volume, you obtain plus and minus signs. Without a more pronounced physical distinction, it is possible to quicker miss the buttons, and the frame moves inward once you press.
Twelve South is in advance about precisely how protective the SurfacePad is. From the FAQ portion of the case’s website, the company says, “SurfacePad for iPhone is not really designed to protect iPhone from falls, drops, being run over from a car or dropped from the loo. SurfacePad is meant to guard your iPhone from scratches and scrapes from stuff like car keys, nail files or concrete park benches.” It’s actually less of a case and more of your leather sticker using a cover. The SurfacePad adheres to the rear of the iPhone, and you will take it off and reapply it necessary (though accomplishing this is not really as easy as the organization might have you believe). We like the types of materials, although the SurfacePad is actually difficult to recommend unless your main issue is fashion.
The Vault Slim Wallet from Silk is really a much-less-expensive alternative to sister company CM4’s Q Card Case. It’s basically the same design, except as opposed to a faux-leather back, the whole thing is made of TPU. Just like the Q Card Case, the Slim Wallet can hold three cards, but an elevated arch in their card slot causes the cards to curve to a noticeable degree, which may damage the cards after a while. The Q Card Case’s positive attributes otherwise carry over, but because of the card bending, I’m a lttle bit cautious about the Slim Wallet.
Silk now offers the Armor Tough Case and PureView Clear Case. The Armor Tough Case is a rubber case with interchangeable, polycarbonate-plastic backplates. It’s an excellent case at an affordable price, but it’s thicker than than our top pick, the NGP. The PureView Clear Case, on the flip side, can be a nice pick from the very full category of cases with rubber edges and clear backs, and Silk prices it aggressively. But we’re not terribly fond of this style because of dust’s propensity to have below the transparent back, and because of the ease in which the plastic can scratch. Still, close to others we’ve tested, the PureView Clear Case has pleasant-feeling buttons and well-sized port openings.
With Incipio’s Rival, unlike using the NGP, simply the border is TPU; the rest of the Rival is tough plastic, about .3 mm thicker in comparison to the NGP. The rest regarding the case is largely just like about the NGP, for example the cutouts for your ports and the grade of the button protection. Whilst the Rival is extremely smooth, similar to the NGP, horizontal lines over the lower two-thirds of its back include a distinct texture. It isn’t as neutral because the NGP, but if you love the fashion, it really is a good option.
Tech21’s Evo Mesh, which features the second generation of the company’s shock-absorbing lining, is an Apple Store exclusive. Much like Tech21’s Classic Shell (more about this design below), it’s a rubber case using a colored band walking around the perimeter. The dimensions are virtually identical involving the two. There’s something relating to this one that we like a lot more than the Classic Shell, but it’s tough to put a finger of what which is. Perhaps it’s that the somewhat-obnoxious orange band has become replaced by colors matching the various body shades in the case itself. Overall, though, this situation is way too pricey for the purpose it gives you.
Plastic and rubber using a clear back, the ITSKINS Venum Reloaded drops the ball in relation to covering the iPhone’s buttons. Similar to the setup of Spigen’s Ultra Hybrid, the design of your Venum Reloaded makes virtually no physical distinction in between the button coverage and the other case. This example had also been relatively expensive when last we checked, along with the plastic border frame feels fragile.
Really a greater portion of a fashion case, the Nitro Forged from ITSKINS currently costs a pretty penny at nearly $70. It is made up of rubber skin with machined aluminum caps that attach towards the top and bottom. Thankfully, this design is undoubtedly an improvement over previous versions, which required anyone to make use of an included screwdriver to install and take away the caps; instead, it uses small plastic clips you could place in and take off yourself.
Also from ITSKINS will be the Evolution. A rubber core by using a plastic frame, the Evolution has some curves which help ensure it is feel a little more organic. The big problem would be that the screen rises over the edge of the situation rather than the opposite. Which means that if you drop your handset, there’s a lot more potential for damage to the display compared to other cases.
Incipio makes so many cases that we can’t expect great things out from every one. The Advantage is a plastic slider, a design that’s relatively rare these days. The smooth, matte-finish plastic splits into two pieces for both installation and docking purposes. Although it offers proper button coverage plus a nice protective lip, we found the case to get too tight; pulling it away, specially the bottom cap, is actually a struggle.
Weighing a few grams more than the typical of all of the cases we tested, the DualPro SHINE is really a solid contender from Incipio. It incorporates both plastic and rubber layers, although as an alternative to being molded together, they’re two distinct pieces. The rubber is quite thick but doesn’t dampen the tactility of your buttons whatsoever, plus it still provides acceptable access to the ports. The port openings are exactly like the NGP’s. We looked at the typical DualPro, that features a matte finish. It’s quite nice, but it’s thicker compared to NGP and lacking the mil-spec rating in the CandyShell.
The plastic layer of the DualPro SHINE suits grooves from the rubber, improving the case think that a cohesive unit. We believe one of the most polarizing thing about this case is its texture: Built to appear to be brushed aluminum, it certainly doesn’t feel like that, as well as at least within our tests, the result can be a certain measure of cognitive dissonance. It’s not necessarily a bad thing by any means, but overall it merely doesn’t feel as nice as it looks.
If card storage is vital to you, Verus’s Damda is actually a fine case. Your body is made of black rubber, with nice button protection and properly centered openings to the headphone port and microphone, the Lightning port, as well as the speaker. Coupled to the back is actually a plastic compartment that adds both mass and depth. A plastic door slides ready to accept reveal space for 2, maybe three, bank cards. We initially thought it was a little bit hard to open, though with some cards inside it’s easier to work with yet still secure. This can be a greater portion of a distinct segment case than our pick.
Verus’s Crystal Mixx supplies a transparent window as well as a rubber frame. The rear about this one is plastic, which happens to be one of these two drawbacks. Within our experience with iPhone cases, clear plastic scuffs easily and may show those scratches within dependent on days. This example might not be so bad in the event the frame provided a greater lip. Unfortunately, at .3 mm, it’s one of your shortest lips we saw, and it might lead to problems should you drop your iPhone.
The Protector Case and Voyager Case from Pelican look a good deal alike, and each model is difficult to acquire-Pelican doesn’t sell them online, as well as in our experience they’ve been reliably available only at AT&T retail stores. The Protector is a bulkier, more-angular handle the CandyShell design without any additional benefits, so we’d pass onto it. The Voyager adds port protection and funnels the sound from the speakers forward. It also comes with a belt clip and screen film. We see this model rather than an OtterBox case, as it’s basically overkill. Many people simply don’t need this degree of protection, especially not should they have to fall out of their option to finding it.
PureGear’s Slim Shell Case can be found in seven color combinations, including clear-on-clear. This model is difficult plastic using a rubberized but nonetheless rigid frame. The metal button covers certainly are a really nice addition, helping the case feel more premium. It won’t offer just as much protection being a CandyShell, thus it isn’t a top pick, but this one isn’t a poor option by any means.
One of the initial iPhone 6 cases being publicly sold-we saw it since May 2014-Minisuit’s Frost is undoubtedly an inexpensive TPU skin. Though it does fit, it offers almost no lip, as well as the holes over the bottom are uneven to the point of looking warped.
Monoprice is renowned for inexpensive products of all types. We love to several of the company’s accessories-it makes great cables, for instance-but Monoprice cases generally don’t impress. The materials often feel cheap, and other companies offer higher-quality products at similarly low prices. As an example, the Metal Alloy Protective Case (offered in gold, silver, and cosmic blue) includes a thin, aluminum shell that snaps over a thin TPU skin, with lines matching the iPhone’s antenna breaks. The TPU doesn’t feel as nice as being the material that Incipio and also other companies use, and also the case exposes the Apple logo on the back of the phone.
Monoprice’s Industrial Metal Mesh Guard Case (in black or white) feels somewhat nicer but is much less protective. The plastic shell has includes a cool-looking steel grille over it, nevertheless it leaves the very best and bottom edges unprotected, plus it features the greatest Apple-logo opening we’ve seen on any case.
We looked at the TPU case from Insignia, a Best Buy brand, and it appear to be through the same OEM as Monoprice’s TPU case, but in a higher price.
We don’t just like the Monoprice PC TPU Protector Case as much, though it does offer arguably more protection. This model splits into two pieces, with an inner skin of TPU as well as a polycarbonate shell that snaps into position over it. The situation is fairly very easy to assemble, but once it’s together, it just feels big. It’s both wider and thicker than the NGP, without having obvious advantage aside from price.
Rokform has long focused on ruggedized cases that may get connected to an ecosystem of mounting accessories. Its Sport v3 is not any exception. This plastic and rubber case incorporates swappable magnetic backplates that allow it to connect with various mounting brackets the business sells. Unfortunately, the instruction insert lists a dealbreaker: “Magnet will disable NFC on phone.” Currently the organization claims that this magnet won’t hinder Apple Pay or any antennas, but we haven’t tested this.
OtterBox’s Defender Series is the bulkiest of your cases we’ve tested up to now. Here is the company’s flagship case, the one many people associate together with the brand. It’s composed of a plastic frame that snaps throughout the handset and a thick rubber skin that covers the whole thing. Unlike the majority of cases, this model includes flaps on the vibration control switch, headphone port, and Lightning port-all good things for an extra amount of protection. Additionally, it includes button coverage, but we discovered that it takes more force to depress the volume and power controls than other cases do.
The Defender Series is additionally the only case we’ve tested with built in screen protection by means of a definite film integrated into the frame. Simply because you end up with a amount of space involving the protector along with the screen, very light presses and swipes might not register, which is actually a drawback. Atop the Touch ID/Home button is actually a thin sheet of plastic that didn’t hinder the knowledge in our testing. Even though the Defender Series does expose the Apple logo, the situation at the very least covers it with clear film that prevents it from getting scratched. And also as an added bonus, the Defender Series has a belt holster.
Within the OtterBox family, the Commuter Series represents the next thing down in overall protection. Instead of plastic internally and rubber on the exterior, the layers are reversed. The situation still offers port coverage, although the switch about the iPhone’s left side remains exposed. Thankfully, the buttons depress far more easily. As opposed to a permanent screen protector, OtterBox includes an optional film with this case. The Apple logo is once more exposed, this period without having plastic covering it. Besides the port protection, this situation offers no obvious benefits over a CandyShell, as well as the dimension is a drawback that keeps this model from earning a high spot.
The Symmetry Series is actually a relatively recent addition to the OtterBox lineup and also the slimmest of them all. It seems like a direct solution to the CandyShell, using its dual-layer design. This case provides the same measure of protection as our top choice plus a substantial lip. It’s taller and wider, though, with a higher price. The largest benefit is with a matte-plastic back, it won’t show the scratches that a CandyShell does.
OtterBox’s newest case, the Statement Series, is definitely an iPhone 6/6s-specific case. An iPhone 6/6s Plus version exists, but unlike OtterBox’s other lines, this series offers no version for older iPhones or other flagship smartphones. It’s also one of the few OtterBox cases that put aesthetics first, with its large back-panel window and leather-covered lower quarter being its key distinguishing features. We’re testing the Statement today, and we’ll decide whether it should join our picks soon.
The Tough Candy Cases Candy Clip Series is a pretty crazy proposition: For $30, you get a hard-plastic X-shaped piece that snaps onto the back of the iPhone, covering its corners and several of the edges but leaving the buttons and most of the sides exposed. No thanks.
Urban Armor Gear’s Case is one from the only cases we’ve tested to fulfill military drop-test standards. It’s excellent as a protective case, but its industrial aesthetic lacks the broad appeal of simpler designs like those from Incipio and Speck. UAG also combines plastic and rubber in such a case, but rather than a glossy finish, it uses a matte one, with an industrial appearance that appropriately matches the brand’s name. With ridges and fake screws, it looks like something which would not be out of place on the construction site. We do take issue with both the small, rectangular holes on the rear of the case-about a quarter of the way from your top or bottom, respectively, they expose part of the logo and also the top 1 / 2 of “Phone” in the iPhone label. It’s a strange design decision with an otherwise impressive case. On the other hand, this model does include a screen film, whereas most iPhone cases don’t these days.
Tech21’s entire product lineup is founded on D3O, an authorized material the corporation uses in each and every one of the cases. Mostly contained in the borders of Tech21 cases, the bright-orange material should certainly remain soft when at rest but automatically harden upon impact, dissipating the force and ultimately preventing injury to your phone. The company really likes to show off the stuff; all of its cases are at least translucent, or even transparent, throughout the edges.
From Tech21, we tested the Classic Shell, Classic Shell Cover, and Classic Shell Flip. First is the most basic, a glossy TPU skin that’s wider in comparison to the NGP, on account of the layer of D3O. We’d want to see a bigger lip than this case offers, and also the buttons can be a bit squishier than we generally prefer. The Classic Shell Cover keeps a similar frame but replaces the TPU about the back by using a hard-plastic plate, and it has an attached cover to shield the iPhone’s display. Everything else works exactly like using the standard model, along with the lid features a cutout across the earpiece to help you speak about the phone with it closed. The Classic Shell Flip is basically the identical, only rather than plastic this situation features a leather feel (it looks to be the fake stuff), and the lid comes around from your bottom instead of the side. We discover that lids get in the way a lot more than they help, so neither of those covered models excites us, as well as the soft buttons and wider body in the Classic Shell prevent it from getting a recommendation.
From iLuv, we received two cases for evaluation: the Aurora Wave and Gelato. The very first is an easy silicone skin with a grid in the back that glows at night. In terms of body coverage, the case lives around what we’re looking for, but making this type of design involves a minimal amount of difficulty. As we’ve often found with cases of this style before, the vertical edges can pull away from the body of your phone more readily than with other cases, allowing dust along with other particulates to get underneath. The Gelato, on the flip side, is TPU iphone7 case by having an attractive checkerboard pattern in the back. It appears and feels very good, nevertheless the .33-millimeter lip is way too short.
Poetic’s Atmosphere is really a thin case made of dual-molded polycarbonate plastic and TPU. The softer material rings the front edge to create a small lip, and in addition it runs within the antenna breaks on the rear of the phone. Although this transparent case initially seems like a fantastic option for individuals that need a slim protector yet still want to demonstrate their iPhone, it falls short on account of button protectors that need a lot of force to press.
Macally shipped us a handful of different cases, but two of them are styles we simply can’t recommend. The Metallic Snap-On Case along with the Flexible Protective Frame come in a variety of colors, however the former is a shell, and the latter is a bumper that protects the sides but leaves the scratchable back exposed. The Durable Protective Case, in comparison, does offer more thorough protection, however it isn’t an original design. A combination TPU skin and hard-plastic frame, this case type of seems like an armadillo from the back. We’ve already seen no less than one other company supplying the same case, and that we weren’t impressed with that case’s aggressive looks either.
New Trent’s Alixo 6S isn’t necessarily the prettiest case around, but it is one in the more original designs we’ve found in the pile. This two-piece case includes a front frame (black- and white-rimmed versions are contained in the package) plus a silicone rubber and plastic back. You simply snap the phone into your selection of frame and after that insert it in to the back piece, consisting of flip-open port protectors. The level of protection this model offers for the pricing is impressive, because it features a built in screen film and Touch ID coverage. Nevertheless the latter ends up being the Alixo 6S’s downside: Even though the fingerprint sensor does work with the thin material over it, we found it to be less reliable, requiring more tries to unlock the device.
Marblue’s ToughTek is really a thick silicone rubber case that comes with a screen protector. While we don’t doubt this thing will be able to tolerate some significant drops, the ToughTek is large-3 inches wide, 5.8 inches tall, and .6 inch deep-and particularly difficult to get in and out of tight pockets because of the grippy material. It might not be described as a bad option if you’re handing your iPhone 6 to kids.
The Elite, also from Marblue, takes its inspiration in the CandyShell, while incorporating an Aztec-like pattern. The plastic and rubber layers intersect in horizontal and vertical lines, with the latter material sticking up above the hard plastic. By far the most intriguing thing about this case will be the pair of inch-long ridges, one on each side. They’re made to use an array of accessories, such as a belt clip. We’ll be keeping an eye out for these accessories, and we’ll see whether they boost the need for the way it is.
We had high hopes for your Spigen Capella, which comes in multiple colors. Its setup is nearly the same as the CandyShell’s, with rubber inside and plastic outside. The big difference, and also the reason we were excited about it, is it’s much slimmer, measuring about 2 mm thinner from front to back. This is certainly partly as a result of smaller, half-millimeter lip around the screen. One of the editors loves just how the case’s slight curve feels, comparing it towards the iPhone 3G. Judging from the feedback we’ve seen from readers and Amazon reviewers, lots of people don’t like that shape as much as we all do.
Although the Capella isn’t as deep because the CandyShell, it is actually a bit taller, contributing to 3 mm wider. This width eventually ends up being problematic for two reasons, one on either edge. In the iPhone’s left side, the switch is significantly harder to toggle, as it’s deeply recessed inside of the rubber border; should you don’t have nails to communicate of, moving it backwards and forwards will likely be tough. On the other side, the Sleep/Wake button takes a surprising quantity of pressure to activate. If you’re willing to deal with those drawbacks, the Capella is otherwise worth taking into consideration like a CandyShell alternative.
With its Revolution case, Poetic is looking to contend with companies like OtterBox at a lower price. The truth begins with a plastic frame that snaps on the front in the iPhone; a specific sheet of plastic protects the screen while leaving the sensors at the top along with the Touch ID button at the end exposed. A rubber and plastic body fits throughout the back, snapping into position with all the front piece. The whole thing feels quite sturdy, the buttons click well, and the flap on the Lightning port is a nice amount of extra protection.
Supcase’s Unicorn Beetle Pro Holster offers a similar proposition. The greatest difference between this model and the Revolution is that it has a plastic belt holster. Having roughly exactly the same dimensions because the Poetic case, this model requires an installation that’s virtually the identical. This example adds a few flaps for coverage, namely across the side switch along with the headphone port as well as the Lightning port. While it’s a very solid-feeling case, we immediately called the company’s claim of dust-proof construction into question, mainly because it leaves openings for dust to go into, like the fully exposed speaker. Presently, Amazon users are typically keen on it, with 127 reviews plus a 4.1-star (from five) rating, but we’ve seen quite a few three- and four-star reviews.
Relative newcomer Supcase has a variety of iPhone 6 cases, actually, the majority of that happen to be area of the “Unicorn Beetle” family. The Slim Armored Protective Case is a lot like Urban Armor Gear’s case in that it’s protective, although the design is quite specific, meaning it likely won’t attract the identical wide swath of men and women as something a little bit more generic. The plastic and rubber case feels sturdy and it has a few of the clickiest buttons of the we tested. When it comes to lip, it’s only about .5 mm, so it’s smaller than we’d like, and also the case makes no mil-spec claims. If you want the appearance, it’s not necessarily a bad choice otherwise.
Supcase also sells the Hybrid Clear Bumper Case, which combines a specific-plastic backplate with a TPU bumper. That polycarbonate back won’t absorb the maximum amount of shock as being the thick rubber border, but it’s a sensible way to flaunt Apple’s design.
In a previous version with this guide, we named Logitech’s Protection [ ] as a more-protective pick. It possesses a very similar design, with the key benefits of a matte finish and embedded magnets that give it time to connect to mounting accessories. Unfortunately Logitech has confirmed that it’s no longer selling the case, which happens to be currently on clearance at Best Buy.
Not one other case we tested is established exactly the same way as Maxboost’s DuraShield Series (now named DuraSLIM). Like a number of other models, it uses both rubber and plastic components, but here the rubber is a bumper that wraps throughout the iPhone’s border, and also the plastic snaps set up over it while covering the back of the handset. Inspite of the unusual design-or simply for doing it-the way it is offers superior protection in comparison with many more we’ve seen. It includes a 1-mm lip, plus speaker and Lightning-port protection. Additionally, it redirects the audio ports forward, meaning the sound comes at you, instead of down; the design has no affect on audio quality, thankfully. As for the Lightning port, it stays protected underneath a rubber tab that you could flip out when you really need access.
Few case manufacturers actively warn their product doesn’t offer drop protection, but just such a message appears around the Amazon listing for Maxboost’s Liquid Skin. Extremely thin, this transparent-TPU case adds almost no bulk towards the handset, not a protective lip. It’s superior to a shell mainly because it offers button protection and cutouts to the ports, even if they are quite tight. But with such a warning from the case maker itself, we can’t recommend the Liquid Skin for many individuals. If you’re going to employ a case, you should use something that’ll endure a drop.
Maxboost’s Crystal Cushion and that i-Blason’s Halo Series are almost identical to each other and also can be small tweaks on a single reference design. Have rubber frames-the Halo Series offers six colors, plus clear-with transparent plastic backplates. The Maxboost case’s edges tend to be more squared-off, whilst the i-Blason’s are rounder. Both offer good body coverage and responsive buttons, nevertheless the lip around the screen is virtually nonexistent, especially on the Halo Series. Combine by using the tendency for clear plastic cases to scratch and also to expose trapped dust underneath, and these cases aren’t top picks.
The Maxboost HyperPro Series is made for all intents and purposes a thicker version in the Incipio NGP. Available only in black, it uses two layers of TPU to protect the iPhone, and it measures 10.2 mm thick; it’s also wider and taller than our pick. The buttons press well and it includes a protective lip, but we can easily find no real benefit to this case over the NGP, apart from savings of just a couple dollars.
One of just a couple of slider-style cases around, Maxboost’s Vibrance Series delivers a different build than the majority of the cases we tested. A tough-plastic case, it splits into two pieces, both lined using a soft fabric over the back that’s designed to prevent damage during installation and removal. Instead of pushing the phone into the case, you accomplish the base cap, slide the phone in the top, after which push the pieces together again. Much much like the STM Harbour, this type of design permits you to keep the iPhone thoroughly protected most of the time, and also to plug it into docks when necessary. The lip is somewhat short, though, and pulling from the Vibrance’s bottom cap is harder than flipping in the Harbour’s bottom. Maxboost now offers only one color choice, salmon by using a gold cap, which can not appeal to as many people as increasing numbers of basic colors would.
If you find the CandyShell to be too big, you won’t be impressed with Speck’s MightyShell, which comes in black, orange, purple, pink, and clear variants. This model has a couple of key differences. First may be the extra layer of TPU material that can help absorb shocks to some greater degree; it adds 2 mm in both width and height, as well as .5 mm to the thickness of the case. Speck claims that it new design will “double MIL-STD-810G drop test standards,” but we can’t tell whether which means the case is tested to live drops from two times as high or it means the situation can tolerate the regular 4-foot drops twice as many times. One aspect of the case we actually appreciate may be the hard-plastic exterior, that is matte rather than glossy, therefore it won’t show scratches as readily because the standard CandyShell. For your price, we expect not only claims of better drop protection; instances in which this example would survive but a CandyShell wouldn’t are too ambiguous to justify the charge.
Among ultrathin cases, Shumuri’s SLIM looks and feels much like Caudabe’s The Veil XT, as a result of the lack of the typical Veil’s screen-protection lip. But it’s also missing both Veil models’ camera-lens protector. The same thing goes for Monoprice’s Ultra-thin Shatter-proof Case (in clear frost, ice blue, and smoke) and Totallee’s The Scarf (for iPhone 6 and iPhone 6 Plus).
Rearth USA’s Ringke Slim (for iPhone 6 and iPhone 6 Plus) offers both a screen-protecting lip and bottom-edge coverage, as well as thicker plastic for extra protection. However, we’re not fans of their aesthetics-since the case’s rigid plastic is thicker, the corporation has added a tiny slit to every corner to make putting the truth in your phone easier. The design is useful enough; we just don’t like the actual way it looks.
Power Support’s Air Jacket and SwitchEasy’s Nude (for iPhone 6 and iPhone 6 Plus) are glossy-plastic cases that are slightly thicker than Caudabe’s The Veil. The former provides good coverage along the phone’s bottom edge but just has the particular faintest of any screen-protection lip. The latter has neither.
Amzer’s Crusta may not look like an excellent value at $35 (iPhone 6) or $45 (iPhone 6 Plus) at the time of this writing, although the package includes not only a fundamental case. The situation itself uses a two-piece snap-together design having a rubber bumper along with a glass back that lets the iPhone’s rear show through. The glass likely won’t show scratches as easily as similar cases we’ve seen using a plastic back, nevertheless, you will still see any dust, hair, or some other particulates that will get beneath the glass. Amzer includes a second part of glass to protect the phone’s screen. The case winds up being bulkier than we prefer-the iPhone 6 version is 14.4 mm thick, including the phone-but it’s one of your better cases we’ve seen from Amzer, an organization otherwise recognized for inexpensive, nondescript accessories.
NewerTech is known more for computer accessories than smartphone add-ons, but the company does give a collection of cases called NuGuard KX (for iPhone 6 and iPhone 6 Plus). Made more for drop protection than sleekness, the NuGuard KX incorporates a thick layer of gel material that absorbs and evenly distributes shocks. The situation is pretty bulky, yet an opening on the rear of the situation for the phone’s Apple logo actually subtracts from your overall level of protection. We like the NGP.
We now have varying levels of praise for 3 cases from Griffin Technology. The Survivor Slim (for iPhone 6 and iPhone 6 Plus) is our least favorite of them. This bulky rubber case feels a lot more like an accessory to get a kid’s toy compared to a smartphone. It could be an effective case if children frequently make use of your phone, but we suspect that many adults will prefer something slimmer.
We love to the Survivor Core (for iPhone 6 and iPhone 6 Plus) and Clear Identity (for iPhone 6 and iPhone 6 Plus) better. Both enable the handset’s straight back to show by way of a clear back panel. The first kind has rubber edges, and its rubber corners protrude somewhat, helping to cushion the iPhone against drops-although the outcome is that it’s a bit larger than a conventional case. The All Clear Identity, on the flip side, includes a transparent back with translucent-rubber edges. The issue, as with all cases sporting a precise back, is both cases show any gunk that gets beneath the plastic. For many people, which might be a suitable compromise in the case designed to enable you to view your phone’s own surfaces, but we generally prefer something translucent or opaque. Neither the Survivor Core nor the All Clear identity can be a bad option, but neither particularly excites us.
Belkin’s Grip Case for iPhone 6 is a great replacement for our top pick, but it doesn’t quite create the top tier. The design is nearly the same as that relating to the Incipio NGP, as it’s a one-piece polyurethane case. The biggest difference is across the phone’s bottom edge: As opposed to having separate openings for the headphone jack, microphone, Lightning-connector port, and speaker, the way it is exposes the very last two through one long opening. A little indentation within the plastic covering the foot of the phone allows for use with accessories including Apple’s Lightning-connector adapters. It is a nice feature which we haven’t seen on other cases, although we worry that the thinness of your material here, along with near to the Ring/Silent switch, may make it more vulnerable to ripping. Wirecutter editor Michael Zhao also finds the case’s button coverage to get somewhat problematic, as he doesn’t that way they’re nearly flush with the case.
Amongst the cases brought to us for consideration, we also dismissed numerous models right from the start. We cut Spigen’s Slim Armor, Slim Armor S, Tough Armor, and Tough Armor S, as well as Verus’s Thor, Iron Shield, and Dandy Diary, plus PureGear’s DualTek, because of their Apple-logo-exposing holes around the back. They do a good job of protecting your phone otherwise, but we can easily think of no reason to recommend them for many people when existing hole-free options are as good or better.
We dismissed several shell cases because, while we mention above, they provide a minimal volume of coverage for your device’s body. Among these were the Aluminum Fit, Thin Fit, and Thin Fit A from Spigen. The same thing goes to the Neo Hybrid EX, Spigen’s bumper case, which provides even less protection.